| Automated Gauge Calibration System. Pressure Standards are extra. |
| Includes GaugeCalHP, FastCalXP, NPT CPF Fittings, Fine Adjust, Footswitch, Carrying Case, USB Adapter, and Rebuild Kit. |
-
Calibration lab in a box! This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It allows you to do a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate. • Gauge / Chart recorder / Transmitter calibration system • 7 to 10 times faster than a deadweight tester • Reduce transcription / calculation errors • 0.1% of reading accuracy up to 15 000 psi (1000 bar) when using the XP2i as the reference or 0.05% of reading accuracy up to 5000 psi (300 bar) when using the 30 Series as the reference • Easy to use and install, wizards guide you through setup • Includes a weather-proof rolling case that can be used as a portable bench
-
Connect Quick-test XT hoses to a male NPT pressure gauge. It allows one to connect a hose to a pressure gauge, calibrate it and remove it without a wrench or thread sealant.
- A unique design allows connection to any male NPT pressure gauge connection using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
Connect a hose on one side of a panel, wall or enclosure with female NPT on the other side
- Bulkhead seals so no liquid or moisture can get into a control panel or enclosure
- Use to connect fittings on the inside of an enclosure to a Quick-test hose on the outside of the enclosure
- Will connect through a wall that is up to 0.5 in (1.3 cm) thick
- Made in USA
-
Make a bubble-tight connection to any Swagelok, Parker, Hoke, SSP, Tylok or equivalent tube fitting without a wrench
- An excellent solution for connecting to tube fittings for pressure calibration, gas sampling, pressure reading and testing
- A unique design that seals on an o-ring to prevent damage to a tube fitting
- Make and remake hundreds of times without over-tightening a tube fitting
- Made in USA
-
Make a bubble-tight connection to any Swagelok, Parker, Hoke, SSP, Tylok or equivalent tube fitting without a wrench to 15,000 psi
- An excellent solution for connecting to tube fittings for pressure calibration, gas sampling, pressure reading and testing
- A unique design that seals on an o-ring to prevent damage to a tube fitting
- Make and remake hundreds of times without over-tightening a tube fitting
- Made in USA
-
Connect a Quick-test hose on one side of a panel, wall or enclosure and a tube fitting on the other
- Bulkhead seals so no liquid or moisture can get into a control panel or enclosure
- Use to connect tube fittings on the inside of an enclosure to a Quick-test hose on the outside of the enclosure
- Will connect through a wall that is up to 0.5 in (1.3 cm) thick
- Made in USA
-
DV0V (23 inHg / 650 mm Hg Vac) pump, no gauge adapter, with 3ft hose, 1/4" MNPT process conn. Generate vacuum to calibrate vacuum devices in the field Light weight, compact pump generates 23 inHg (584mm Hg)vacuum with ease Large volume fine adjustment piston provides precise control, even at very low vacuums Modular design makes field maintenance quick and easy Precisely vent pressure with soft seated bleed valve Two outlet ports provide connections for both pressure reference and for device under test thus eliminating a tee Low volume Quick-test hose, gauge adapter and process connection can be attached to pump without thread sealant or a wrench Rugged, all metal construction reduces pressure changes due to temperature fluctuations Made in U.S.A. Item Includes Hand Pump - DV0V Assembly (DV0V) Hose - Quick-test 6900 psi hose, brass hose ends, 3 ft (92 cm) long (QTQT-HOS-3ft) Hose Adapter - 1/4" male NPT x male Quick-test, no check-valve, brass (QTHA-2MB0)
-
DPPV (+125 psi to -23" Hg) pump, no gauge adapter, with 3ft hose, 1/4" MNPT process connection Generate either a vacuum or a pressure for calibrating low pressure or vacuum instrumentation using an external pressure calibrator. Features
- Generate either 125 psi (8.6 bar) pressure or 23 InHg (584 mm Hg) vacuum with the same pump
- Unique design allows the user to convert from pressure to vacuum by simply twisting a knob, even with gloves on
- Two outlet ports allow connection to reference pressure gauge or pressure calibrator as well as device under test, thus eliminating a tee
- Large volume fine adjustment piston provides precise control, even at very low pressures
- Precisely vent pressure with soft seated bleed valve
- Made in U.S.A.
-
The SP0V gas sampling pump can pull low pressure gas from a well and boost it to 25 psi to pump it into a sample cylinder Hard Anodized aluminum body and stainless steel fittings so no issues with corrosion, cracking or cross contamination of the sample Inlet and outlet hose has Nylon inner core tube which does not affect the sample Low compression rate will not adversely affect the sample by bringing the gas close to the hydrocarbon dew point (25 psi/2 bar) Hydrocarbon-free lubricant does not contaminate the sample with any foreign hydrocarbons Designed in accordance with API MPMS Chapter 14.1 on natural gas sampling Ideally suited for use with the purge and fill method of gas sampling Made in USA
-
Connect to any male 37 degree flare adapter or tube
- Connect to male AN flare connections without a wrench
- Excellent for use in Aerospace and marine use
- Cap adapters off when not in use
- Made in USA
-
Connect a male 37° flare AN/JIC fitting to a Quick-test hose without a wrench
- A unique design allows connection to standard male 37° flare fitting using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
Connect a male 37° flare AN/JIC fitting to a Quick-test hose without a wrench
- A unique design allows connection to standard male 37° flare fitting using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
The T-900 Series pneumatic hand pumps generate pressure and vacuum with precision and ease, allowing users to fine-tune the pressure delivered with every stroke. A built-in relief valve and dual pressure output enable safe and simple operation. The T-965 and T-975 are available with a button valve, making them capable of switching easily from pressure to vacuum generation • Vacuum & Pressure Range: -25 inHg to 30 psi or -27 inHg to 580 psi • Lightweight, compact design • Two outlet ports • Protected shuttle valve • Fine adjust sensitivity to 0.01 psi • Adjustable stroke • T-975-CPF model includes CPF hose and fittings
-
The T-600 Series is a lightweight and portable hydraulic hand pump, specifically designed for high pressure applications. A fine adjust allows precise control of pressure, while a vent valve provides quick and positive shut-off and pressure release. The pumps are compatible with petroleum-based oils or hydraulic fluids. • High Pressure Range: 0 to 5000 psi • Easy to use fine adjust • Two outlet ports • Large reservoir • Eliminate / Bleed air with CPF fittings • T-620H-CPF includes CPF hose and fittings TO ORDER ACCESSORIES AND REPLACEMENT PARTS ONLY SELECT "NONE" FOR YOUR PUMP SELECTION
-
The P014 hydraulic jack pump (System E) is an extremely effective pressure pump designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle. • Pressure Range: 0 to 10 000 psi / 700 bar • Easy to use fine adjust • Adjustable reference port • Eliminate / Bleed air with CPF fittings • Portable or permanent bench mounting
-
Type T hydraulic comparator (System F) is a self-contained high volume pressure source capable of producing pressure up to 15 000 psi. It is ideal for testing gauges and setting hydraulic relief valves and pressure switches. Multiple models are available for hydraulic oil, water, or both. • Pressure Range: 0 to 15 000 psi • High and low volume settings • Two outlet ports • Large fluid capacity • Fine adjustment up to 3500 psi • Compatible with water and oil • T-1-CPF includes CPF fittings
