-
CPF Fittings and Hose are a new line of quick-test pressure fittings for calibration and test applications -- designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 15 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidentally disconnect from a pressurized system. It can also be used as a bleed point. Each fitting is machined in 316 Stainless Steel and laser markings indicate the fitting type, size, part number, and Maximum Allowable Working Pressure to prevent a mismatched connection. An industry-first patented o-ring connection allows CPF Fittings to maintain a leak-free seal up to 10 000 psi with only finger-tightening. This offers an alternative to commonly-used NPT Fittings, which require technicians to wrap their fittings in thread tape and use a wrench to tighten each installation. Unlike other quick-change fittings, the O-rings in CPF Fittings are also easily replaceable. CHECK ITEM DESIRED AND CHOOSE QUANTITY TO THE LEFT OF LINE ITEM FOR EACH ITEM THAT IS BEING ORDERED
-
Connects Female NPT to Quick-test hoses with brass or stainless steel hose ends.
- Ideal for connecting to pressure transmitters or other devices under test using thread sealant
- Quickly connect and disconnect Quick-test hoses for testing, calibrating and sampling
- Made in USA
-
Cap and chain for any male Quick-test adapter with a cap and chain Seals any male Quick-test adapter to 5000 psi (345 bar) Install on any Quick-test adapter for permanent installation in the field Made in USA
-
Outlet ports used on hand pumps, nitrogen sources, volume controllers Made in the USA
-
Connect a Quick-test hose to a pressure gauge or any device with a male NPT connection using thread sealant and a wrench
- Connect to pressure gauges with NPT connections
- Adapt to a wide range of Male NPT process connections
- Made in USA
-
Connect two Quick-test hoses or two Quick-test adapters together, depending on the union Quick-test connection makes connecting two hoses together quick and easy Made in USA
-
Make a bubble-tight connection to any Swagelok, Parker, Hoke, SSP, Tylok or equivalent tube fitting without a wrench
- An excellent solution for connecting to tube fittings for pressure calibration, gas sampling, pressure reading and testing
- A unique design that seals on an o-ring to prevent damage to a tube fitting
- Make and remake hundreds of times without over-tightening a tube fitting
- Made in USA
-
Use to mount gauges on Ralston Instruments model APGV, HPGV, XHGV hand pumps Swivels allow the user to easily switch gauges on a single hand pump Made in USA
-
Quickly connect a pressure calibrator or other pressure device with Female NPT connections to Ralston hand pumps or nitrogen calibration equipment
- Connect to any pressure calibrator or pressure module with Female NPT connections
- Allows the calibrator and pressure source to be easily disconnected and stored separately
- Made in USA
-
Plug a hose to prevent fluid from leaking out Pressure-tight with just your fingers Made in USA
-
Connect to a pressure gauge or other device with Male NPT connections to a Ralston hand pump or nitrogen calibration device
- Install with thread tape once onto any male NPT pressure gauge then use the Quick-test connection to quickly connect or disconnect from any Ralston hand pump, nitrogen calibration device or other Quick-test adapter
- Saves the threads on a pressure gauge by not needing to make and remake the connection with thread sealant
- Made in USA
-
A removable cap provides easy access to connect a Quick-test hose to the process for calibration purposes and is easily sealed bubble-tight again when calibration is complete
- Connect to pressure transmitters, EFMs, Flow Computers and other NPT devices under test using thread sealant for a permanent connection
- A Cap and chain makes calibration easy and quick by connecting and disconnecting a hose without a wrench or thread sealant
- Made in USA
-
Connect to Female Metric thread comparators, pressure pumps and devices under test Excellent for use in the laboratory for adapting Female Metric pressure comparators to Quick-test Use with any Quick-test Quick-connect adapter or hose Made in USA
-
Turn any Quick-test XT adapter into a permanent installation with the addition of a cap and chain Seals any male Quick-test XT adapter Install on any Quick-test XT adapter for permanent installation in the field Note that these are not compatible with QT or QS hoses. Please use only on Quick-test XT adapters Made in USA
-
Excellent for safely connecting two Quick-test hoses through an enclosure, truck, or panel wall Bulkhead seals so no liquid or moisture can get into a control panel or enclosure Use to connect a Quick-test hose on the inside of an enclosure to a Quick-test hose on the outside of the enclosure Will connect through a wall that is up to 0.5 in (1.3 cm) thick Made in USA
-
Connect a Quick-test hose on one side of a panel, wall or enclosure and a tube fitting on the other
- Bulkhead seals so no liquid or moisture can get into a control panel or enclosure
- Use to connect tube fittings on the inside of an enclosure to a Quick-test hose on the outside of the enclosure
- Will connect through a wall that is up to 0.5 in (1.3 cm) thick
- Made in USA
-
Connect a Quick-test hose directly to a DP transmitter using the bleeder port when the transmitter is not mounted on a 3 or 5 valve manifold or when the manifold is not easily accessible. This unique fitting makes a metal to metal seat on the transmitter and a Quick-test hose can be attached on the other side Connects through the bleeder screw port on a DP transmitter Made in USA
-
Connect to SAE/MS ports on pressure calibrators, pipelines and other processes Connect using an o-ring seal avoids issues with vibration, heating and cooling Excellent for aerospace and automotive connections with female SAE/MS ports Made in USA
-
Connects Female NPT to Quick-test XT 10,000 psi hoses
- Ideal for connecting to pressure transmitters or other devices under test using thread sealant
- Quickly connect and disconnect Quick-test hoses for testing, calibrating and sampling
- Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses
- Made in USA
-
Connect a Quick-test XT hose to an NPT pressure gauge or any Male NPT device using thread sealant and a wrench
- Connect to pressure gauges with NPT connections
- Adapt to a wide range of Male NPT process connections to 10,000 psi
- Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses
- Made in USA
-
Microbore hoses that provide a very quick, low volume, high pressure way of connecting to any pressure instrumentation, hand pump, calibration source or device under test
- Low volume reduces the pumping effort or compressed gas usage in pressure calibration
- No thread sealant required – connect to adapters without wrenches, thread sealant or thread tape
- Bubble tight connections to 6900 psi (475 bar) with no moving parts reduces maintenance to almost zero
- Hose is hard to break and very flexible
- Adapt from hose to virtually any device under test with only one connection
- Silver color dramatically reduces the effect that changing temperature has on pressure stability
- A corrosion resistant strain-relief on each hose end reduces wear and dramatically increases hose life
- Hose is excellent for inert gas applications (except Helium and Argon)
- Hose is pin-pricked for use in Natural Gas applications
- Made in U.S.A.
-
Connect to hoses, comparators and pressure references with Male Medium Pressure adapters Connect to Crystal Engineering CPF hoses and GaugeCal XP Comparators Connect to Medium pressure connections
-
Connect 2 Quick-test XT 10,000 psi hoses together quickly and easily Quick-test XT connection makes connecting two high pressure hoses together quick and easy Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses Made in USA
-
Quickly connect a pressure calibrator or other pressure device with Female NPT connections a to Ralston hand pump or nitrogen calibration equipment to 10,000 psi
- Connect to any pressure calibrator or pressure module with Female NPT connections
- Allows the calibrator and pressure source to be easily disconnected and stored separately
- Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses
- Made in USA
-
Connect Male NPT pressure gauge or other Male NPT device to a Ralston hand pump or nitrogen calibration device to create one side of a quick-disconnect to 10,000 psi
- Install with thread tape once onto any male NPT pressure gauge then use the Quick-test connection to quickly connect or disconnect from any Ralston hand pump, nitrogen calibration device or other Quick-test adapter
- Saves the threads on a pressure gauge by not needing to make and remake the connection with thread sealant
- Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses
- Made in USA
-
Connect a hose on one side of a panel, wall or enclosure with female NPT on the other side
- Bulkhead seals so no liquid or moisture can get into a control panel or enclosure
- Use to connect fittings on the inside of an enclosure to a Quick-test hose on the outside of the enclosure
- Will connect through a wall that is up to 0.5 in (1.3 cm) thick
- Made in USA
-
Connect to any Medium Pressure connection Ideal for connecting to Autoclave Engineers, Butech, HIP or Parker Medium Pressure connections Connect to Crystal Engineering pressure gauges or pressure calibrators with Female CPF pressure connections Made in USA
-
Connect a Female High Pressure 60 degree coned and threaded pressure fitting to a Quick-test hose Excellent for connecting to Autoclave Engineers, Butech, HIP (High Pressure Equipment), Parker or equivalent High Pressure coned and threaded connections, valves, tees and unions Metal to metal seal provides leak-free service Made in USA
-
Connect a Ralston Quick-test hose to a 1620 connection Adapt any Hydrotechnik Minimess or equivalent 16 x 2.0 connection to a Ralston Quick-test adapter Made in USA
-
Connect a Female 60 degree coned and threaded pressure fitting to a Quick-test XT 10,000 psi hose Excellent for connecting to Autoclave Engineers, Butech, HIP (High Pressure Equipment), Parker or equivalent High Pressure coned and threaded connections, valves, tees and unions Metal to metal seal for 10,000 psi service Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses Made in USA
-
Connect to any male 37 degree flare adapter or tube
- Connect to male AN flare connections without a wrench
- Excellent for use in Aerospace and marine use
- Cap adapters off when not in use
- Made in USA
-
Connect Quick-test hoses to a male NPT pressure gauge. It allows one to connect a hose to a pressure gauge, calibrate it and remove it without a wrench or thread sealant.
- A unique design allows connection to any male NPT pressure gauge connection using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
Ideal for situations where frequent calibration of a DP transmitter using the bleeder port is required This unique fitting makes a metal to metal seat on the transmitter and a Quick-test hose can be attached on the other side Connects through the bleeder screw port on a DP transmitter Made in USA
-
Connect three hoses or a combination of 3 hoses, adapters and hand pumps or manifolds Durable forged construction Tee has full flow through each of the ports Made in USA
-
Connect a hose to an adapter that is in a hard to reach place Ideal for accessing pressure transmitter ports and other equipment that is hard to reach Position pressure gauges for easy reading Durable forged construction Made in USA
-
Connect to pressure gauges, pressure calibrators and adapters easily and quickly Position a pressure gauge for easy reading Connect a Quick-test hose to an adapter in hard to reach places Durable forged construction Made in USA
-
Connect a Quick-test hose directly to a DP transmitter using the bleeder port when the transmitter is not mounted on a 3 or 5 valve manifold or when the manifold is not easily accessible. This unique fitting makes a metal to metal seat on the transmitter and a Quick-test hose can be attached on the other side Connects through the bleeder screw port on a DP transmitter Made in USA
-
Make a bubble-tight seal on any Female NPT pressure device without using thread sealant or a wrench.
- A unique design allows connection to standard female NPT ports using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
Connect to any medium pressure connection Ideal for connecting to Autoclave Engineers, Butech, HIP or Parker Medium Pressure connections Connect to Crystal Engineering pressure gauges or pressure calibrators with Female CPF pressure connections Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses Made in USA
-
Connect a male 37° flare AN/JIC fitting to a Quick-test hose without a wrench
- A unique design allows connection to standard male 37° flare fitting using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- Stainless steel construction
- Made in USA
-
Excellent for safely connecting two Quick-test XT 10,000 psi hoses through an enclosure, truck, or panel wall Bulkhead seals so no liquid or moisture can get into a control panel or enclosure Use to connect a Quick-test XT hose on the inside of an enclosure to a Quick-test XT hose on the outside of the enclosure Will connect through a wall that is up to 0.5 in (1.3 cm) Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses Made in USA
-
Connects Female NPT to Quick-test XT 10,000 psi hoses for permanent installation
- Connect to pressure transmitters, EFMs, Flow Computers and other NPT devices under test using thread sealant for a permanent connection
- Cap and chains make calibration easy and quick by connecting and disconnecting without a wrench or thread sealant
- Note that these are not compatible with QT or QS hoses. Please use Quick-test XT hoses
- Made in USA
-
Make calibrating pressure transmitters a snap by eliminating the need for thread sealant or wrenches when connecting to any female NPT connection
- A unique design allows connection to standard female NPT ports using a pressure-assisted o-ring seal
- Pressure helps to seal the fitting better
- A Cap and chain makes calibration easy and quick by connecting and disconnecting a hose without a wrench or thread sealant
- Stainless steel construction
- Made in USA
-
Connect to any Size Petes Plug for testing, sampling or reading a pressure. Connect from any Pete's Plug directly to a Ralston Quick-test hose, gauge or FieldLab for quick pressure testing "Pete's Plug" is a registered Trademark of Peterson Industries Made in USA
-
Use to slowly or quickly bleed pressure from a line after a calibration is complete Easily connect between the end of a Quick-test hose and the process connection Keep fluid or contaminates out of the hand pump, calibrator or nitrogen control device
-
Connect a Quick-test hose directly to a DP transmitter using the bleeder port when the transmitter is not mounted on a 3 or 5 valve manifold or when the manifold is not easily accessible. This unique fitting makes a metal to metal seat on the transmitter and a Quick-test XT hose can be attached on the other side Connects through the bleeder screw port on a DP transmitter Pressurize to 10,000 psi (700 bar) Made in USA
-
Connect a pressure gauge with Metric male parallel thread to a Quick-test hose A unique design allows connection to any male metric connections using a pressure-assisted o-ring seal Pressure helps to seal the fitting better Stainless steel construction Made in USA
